kbp005 thru kbp10 and rs201 thru rs207 silicon bridge rectifiers reverse v oltage - 50 to 1000 v olts forward current - 2.0 amperes case : molded plastic body t erminals : plated leads solderable per mil-std-750, method 2026 polarity : polarity symbols marked on case mounting position : any w eight :0.069 ounce, 1.95 grams fe a tures mechanica l d at a dimensions in inches and (millimeters) maximum r a tings and electrica l characteristics ratings at 25 c ambient temperature unless otherwise specified. sing le phase half-wave 60hz,resistive or inductive load,for capacitive load current derate by 20%. notes: 1.measured at 1.0 mhz and applied reverse voltage of 4.0 v olts. 2.unit mounted on p .c. board with 0.47 ? x 0.47 ? (12x12mm) copper pads,0.375 ? (9.5mm) lead length. the plastic package carries underwriters laboratory flammability classification 94 v -0 ideal for printed circuit boards low reverse leakage high forward surge current capability high temperature soldering guaranteed: 260 c/10 seconds,0.375 (9.5mm) lead length, 5 lbs. (2.3kg) tension 10 10 0.5 20 28 -60 to +150 -60 to +150 2.0 vo l ts vo l ts vo l ts symbols units amps amps v olts v rrm v rms v dc i ( a v) i fsm maximum repetitive peak reverse voltage maximum rms voltage maximum dc blocking voltage maximum average forward output rectified current at t a =50 c(note 2) peak forward surge current 8.3ms single half sine-wave superimposed on rated load (jedec method) rating for fusing(t<8.3ms) maximum instantaneous forward voltage drop per birdge element at 1.0a maximum dc reverse current t a =25 c at rated dc blocking voltage t a =100 c t ypical junction capacitance (note 1) t ypical thermal resistance (note 2) operating junction temperature range storage temperature range i t c j r ja t j t stg i r a s 2 2 v f a c c/w ma c pf 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 kbp005 rs201 kbp01 rs202 kbp04 rs204 KBP06 rs205 kbp08 rs206 kbp10 rs207 kbp02 rs203 50.0 1.0 0.600(15.24) 0.560(14.22) 0.500(12.70) 0.460( 1 1.68) 0.460( 1 1.68) 0.420(10.67) 0.035(0.9)dia. 0.028(0.7)tp y . 0.105(2.67) 0.085(2.16) 0.160(4.1) 0.140(3.6) 0.200(5.08) 0.180(4.57) + - ac rs-2 0.640(16.25) min 0.50(12.7) min www.shunyegroup.com.cn
r a tings and characteristic cu r ves kbp005 thru kbp10 and rs201 thur rs20 7 2.0 1.6 1.2 0.8 0.6 0 0 25 50 75 100 125 150 175 50 40 30 20 10 0 0.6 0.8 1.0 1.2 1.4 1.5 0.1 1.0 10 100 0.01 0.1 1 10 100 100 10 1 0.1 reverse vo lt age,vo l ts t,pulse dur a tion,sec. fig. 5-typica l junction ca p aci t ance fig. 6-typica l transient therma l impedanc e fig. 3-typica l ins t an t aneous fo r w ard characteristics number of cycles a t 60 hz fig. 2-maximum non-repetitive peak fo r w ard surge current fig. 1- fo r w ard current der a ting cu r ve , t n e r r u c d e i f i t c e r d r a w r o f e g a r e v a s e r e p m a d r a w r o f s u o e n a t n a t s n i s e r e p m a , t n e r r u c f p , e c n a t i c a p a c n o i t c n u j , t n e r r u c e g r u s d r a w r o f k a e p s e r e p m a ins t an t aneous fo r w ard vo lt age, vo l ts single phase half w ave 60hz resistive or inductive load 1 10 100 0.0 1 0. 1 1 2 0 1 0 t j =25 c pulse width=300 s 1%dut y cycle t j =25 c 1 10 100 200 0 20 40 60 80 100 1,000 100 10 1 0.1 0.01 tj=100 c tj=25 c percent of peak reverse vo lt age,% fig. 4-typica l reverse characteristics , t n e r r u c e s r e v e r s u o e n a t n a t s n i s e r e p m a o r c i m , e c n a d e p m i l a m r e h t t n e i s n a r t w / c ambient temper a ture, c 8.3ms single half sine- w a ve (jedec method) www.shunyegroup.com.cn
|
